Build your own Arduino RC All-Terrain Rover with NRF24L01 | DIY RC Robotic Car Tutorial

Подробнее о видео

This time, we make an easily maneuverable remote-controlled Arduino-based Rover/Car. The car can drive on hard surfaces, grass, gravel, dirt, and even rocky terrain!

As I didn't have enough time to finish coding for the additional feature of having an obstacle avoidance mode I could switch to, I'll postpone that update for the near future, hopefully, you'll get to see a short update video on this rover soon.
Hope you guys enjoyed this video! If you did, then please consider dropping a thumbs up, a share, a comment, and subscribe if you haven't already! :D

👕 Grab my exclusive Merch here! -
----------------------------------------------------------------------
👉 Visit my online Storefront:
----------------------------------------------------------------------
☕ Buy me a coffee:
----------------------------------------------------------------------
Instagram: @max.imagination -
Instructables page:
----------------------------------------------------------------------
Disclaimer: Amazon purchase links below are affiliate links. It doesn't cost you extra to buy through those and I just get a tiny commission. Thank you!


TX & RX Rover Codes:


Rover Circuit Diagram:


Rover's wooden panel blueprints:




Materials/parts/components needed for this project:
Homemade Arduino NRF24L01 Transmitter & Receiver (from previous video tutorial) both consisting of Arduino Nanos & NRF24L01s -
(x4) Plastic (BO) TT Geared Motor + Plastic wheels -
(x1) 180° 9G Servo motor (3-pin type) -
(x3) 18650 3.7V Li-Ion battery cell -
(x1) 18650 cell holder (tray) -
(x1) 3-cell 12V 10A BMS (Battery Management System) board -
(x1) L298N 12V Dual H-bridge motor driver -
(x1) HC-SR04 Ultrasonic distance sensor -
(x1) 3A SPDT Toggle Switch -
(x1) 5V Active buzzer -
(x2) 8mm Bright White LED -
(x1) Female DC barrel jack connector port -
(x1) 24-Gauge insulated electrical wire -
(x22) M3 Screws/bolts -
Additional small screws
(x4) long slim screws (for fixating wheels)
(x1) Electronic switch circuit (MOSFET) -
(x3) JST connectors -
Bicycle tube rubber
(x8) Circular container lids
5mm Plywood board
5mm Compressed Posterboard foam
Road Stud (Optional)

🪛🔧🔨 Tools and extra supplies I use:
➡️ Soldering Iron Kit -
➡️ Hot Glue Gun -
➡️ Drill Machine -
➡️ Box cutter/Utility knife -
➡️ X-Acto Hobby Knife -
➡️ Cutting Matt (Green) -
➡️ Needle-nose Pliers -
➡️ Wire Cutters for Electronics -
➡️ Wire-stripping tool (Automatic) -
➡️ Screwdriver kit -
➡️ Heat-shrink Tube Kit -
➡️ Jumper Wire Kit -
➡️ Breadboard for Prototyping -
➡️ Perf Boards, Pin headers, and Connectors Kit -
➡️ Superglue -
➡️ Duct Tape -
➡️ Double-sided Tape -
➡️ Kapton Tape (for battery leads) -
--------------------------------------------------------------------

Music credits:
Song : Ikson - Focus
Music provided by Max Music No Copyright
Video Link :


P3RRY - Invincible [Free Trap]
Trillion - R.LUM.R
Sunny Days - Anno Domini Beats
Forever - Anno Domini Beats
Squadda Bambino Tumblr - Squadda B
--------------------------------------------------------------------

Tags:
max imagination, diy, rc rover, Arduino RC Rover, DIY RC Robotic Car, All-Terrain Rover, Arduino RC Car Tutorial, DIY Robotic Car Project, Arduino Rover Build, DIY Arduino Car, Arduino RC Car Project, All-Terrain Rover Build, Arduino RC Car Kit, Arduino RC Rover Tutorial, Arduino RC Car Design, Arduino RC Car Build, Arduino RC Car Controller, All-Terrain Rover Design, DIY Arduino RC Rover, All-Terrain Rover Tutorial, DIY Robotic Car Tutorial, nrf24l01,ultrasonic sensor

#arduinoproject #arduinorobot #nrf24l01